A morning was spent in the sun (yes, sun!) changing the oil and filter in the Yamaha outboard on the RIB. The gearbox oil also got changed. The RIB gets suspended in mid air by the crane for this little job:
The one benefit is that you get to take it for a burn around the bay afterwards to check all is well. Hooligan time indeed. On the way back, the Captain had a diversion up the river Ely and found Simon and Nikki sitting outside on their lovely timber yacht. As everyone is conscious of "the virus" we kept the regulation 2 metres gap, in fact a bit more.
The new fresh water pump duly arrived from Italy but as it had been in transit for 4 days we felt pretty safe touching the box. Plenty of hand washing afterwards mind you:
Refitting it was a challenge - another example where the 90 degree elbows for the inlet and outlet go tight 3/4 turn after you want them to. Another job for Leak Lock as normal PTFE tape would not bulk the thing out enough. We had to leave the stuff to cure so could not test it straight away:
So here it is without the wiring tidied up and protected.
A day later, firing it up and bleeding it was another highly amusing job. There is a bleed screw on the front - as soon as the pump picks up some water you get a serious shower. Luckily it is fresh water. Way better than #headgate which we went through when replacing the joker valves in both loos. However, things did not go to plan at all. The position of the pumps is pretty much at the maximum height above the water tanks that is allowed and the new one would not prime. No air leaks, no blockages, just not enough "oomph" to prime. Even when pre-filled it would not drag water through. Grr....... Well, something like that was said, quite forcefully really.
What to do? Have a coffee, calm down, look at the plumbing and realise that it will need some serious surgery to drop both pumps down a couple of feet into the space where the stabiliser is housed. We didn't have the fittings needed to do that so a shopping list would have to be made up. Wonderful. Just made the captain's day which didn't improve when he stuck a screwdriver into his thumb whilst replacing a 240v socket that was misbehaving.. Frequent hand washing to avoid the Covid thingy with a plaster on is not simple.
Our plans were getting a bit messier. Coronavirus was causing restrictions in some harbours so it was time for some agile planning (roughly means that like 99.9% of the population we have no idea how this will all develop so we will just wait and see).
If we have to isolate then the boat isn't a bad place to be. Plenty of diesel (might need a little top up), big water tanks, watermaker but that is not commissioned, big fridge / freezer, plenty of power even if the shorepower fails thanks to the generator. Let's see what happens but we guess that this summer will be short on cruising time.....
About us and the boat
About us and the boat:
We were lucky enough to retire early at the start of 2013 so we could head off and "live the dream" on board our Nordhavn 47 Trawler Yacht. The idea is to see some of the planet, at a slow 6 - 7 knots pace. There are no fixed goals or timings, we just had a plan to visit Scotland and then probably the Baltic before heading south.
The idea is to visit the nicer areas in these latitudes before heading south for warmer weather. If we like somewhere, we will stay for a while. If not, we will just move on. So, for the people who love forward planning and targets, this might seem a little relaxed!
The idea is to visit the nicer areas in these latitudes before heading south for warmer weather. If we like somewhere, we will stay for a while. If not, we will just move on. So, for the people who love forward planning and targets, this might seem a little relaxed!
If anyone else is contemplating a trawler yacht life, maybe our experiences will be enough to make you think again, or maybe do it sooner then you intended!
The boat is called Rockland and she is built for long distance cruising and a comfortable life on board too. If you want to see more about trawler yachts and the Nordhavn 47 in particular, there is a link to the manufacturers website in our "useful stuff" section. For the technically minded, there is a little info and pictures of the boat and equipment in the same section
Regards
Richard and June
Friday, 20 March 2020
Monday, 16 March 2020
Preparing for some cruising (when the gales finally abate!)
After the relentless rain and wind and grey miserable weather this winter, there has to be a break soon. Please! So, in preparation we finally got busy. The list was huge and had to be trimmed a lot with some planned upgrades just postponed as although the sniffles were getting better, we were not back to full power yet.
The fuel supply tank fitting was first on the list. If you have a good memory / are incredibly sad you might recall the annoying first go when we discovered that the fitting ended up 3/4 of a turn from tight in the tank to get the valve in the right position.... So annoying. Thanks some so called engineer who thought that was OK to assemble. Hence when removed the first time, it was refitted and sealed with gloop (Leak Lock) just as the factory cowboy did.
This time the plan was to refit it with washer(s) to pack it out and allow the thing to be properly secure and not relying on the gloop. It meant draining about 35 litres of fuel out, 350ml at a time into a jug. A real fun job but as the captain's sense of smell was still non functioning it wasn't as bad as the first time.
The valve was refitted, this time using normal Wurth pipe sealant on the threads and all was well:
Just a little "Leak Lock" overspill from the first rebuild to clean up. Hardly a priority.
Once completed, the annual fuel filter swap ritual could be completed. All 9 of them. The worst is the big Webasto boiler as it has a real old school CAV 296 filter like this one:
which is messier to swap than any of the others owing to where it is, the wiring around it and the need to dig out the O rings that stay in the top casing after you take it to pieces. Memories came back of a pair of old Ford Sabre engines in a Broom motor cruiser that we owned which had two of these on each engine. There you had to hang upside down to replace them and it was always amusing. The one positive about the old technology CAV device is that the filter elements are as cheap as chips.
The genset had the normal 6 monthly oil and filter swap and then some fresh water pump fun ensued. The "backup" Marco UP12/E pump refused to fire up so we were using the original Jabsco unit. The little lights on the Marco pump suggested that it was either drawing too much current or the input voltage was too low. Checked the latter - it was fine.
After removing the pump from the plumbing and wiring the captain started to take it apart to see what was happening. Very quickly he got a bath in rusty water from inside the motor housing. Problem found. It seems that water leaking past the shaft and into the motor assembly is not uncommon with these pumps. The motor innards were toast so a new one was ordered from an Italian supplier who had one in stock for around £70 less than Timage, the UK supplier wanted. Madness. Knowing how difficult it might be to get one ordered from the factory with the Italian Coronavirus problems, we were happy to find a stock unit. Just need to disinfect the box when it arrives perhaps?
There is a bare spot in the cupboard where the second pump is normally mounted for now:
Refitting the flybridge seats and covers on a sunny (albeit chilly) day made us think that there might just be an end to the wind and rain sometime soon. Then we had another gale and torrential rain. Back to normal happened so quickly and cruelly.
The fuel supply tank fitting was first on the list. If you have a good memory / are incredibly sad you might recall the annoying first go when we discovered that the fitting ended up 3/4 of a turn from tight in the tank to get the valve in the right position.... So annoying. Thanks some so called engineer who thought that was OK to assemble. Hence when removed the first time, it was refitted and sealed with gloop (Leak Lock) just as the factory cowboy did.
This time the plan was to refit it with washer(s) to pack it out and allow the thing to be properly secure and not relying on the gloop. It meant draining about 35 litres of fuel out, 350ml at a time into a jug. A real fun job but as the captain's sense of smell was still non functioning it wasn't as bad as the first time.
The valve was refitted, this time using normal Wurth pipe sealant on the threads and all was well:
Just a little "Leak Lock" overspill from the first rebuild to clean up. Hardly a priority.
Once completed, the annual fuel filter swap ritual could be completed. All 9 of them. The worst is the big Webasto boiler as it has a real old school CAV 296 filter like this one:
which is messier to swap than any of the others owing to where it is, the wiring around it and the need to dig out the O rings that stay in the top casing after you take it to pieces. Memories came back of a pair of old Ford Sabre engines in a Broom motor cruiser that we owned which had two of these on each engine. There you had to hang upside down to replace them and it was always amusing. The one positive about the old technology CAV device is that the filter elements are as cheap as chips.
The genset had the normal 6 monthly oil and filter swap and then some fresh water pump fun ensued. The "backup" Marco UP12/E pump refused to fire up so we were using the original Jabsco unit. The little lights on the Marco pump suggested that it was either drawing too much current or the input voltage was too low. Checked the latter - it was fine.
After removing the pump from the plumbing and wiring the captain started to take it apart to see what was happening. Very quickly he got a bath in rusty water from inside the motor housing. Problem found. It seems that water leaking past the shaft and into the motor assembly is not uncommon with these pumps. The motor innards were toast so a new one was ordered from an Italian supplier who had one in stock for around £70 less than Timage, the UK supplier wanted. Madness. Knowing how difficult it might be to get one ordered from the factory with the Italian Coronavirus problems, we were happy to find a stock unit. Just need to disinfect the box when it arrives perhaps?
There is a bare spot in the cupboard where the second pump is normally mounted for now:
Refitting the flybridge seats and covers on a sunny (albeit chilly) day made us think that there might just be an end to the wind and rain sometime soon. Then we had another gale and torrential rain. Back to normal happened so quickly and cruelly.
Subscribe to:
Posts (Atom)




